Determining the Safe Speed for Curves

35 MPH speed curve sign

As a vehicle approaches a curve, the driver will hopefully slow down and negotiate the curve safely. This is possible because signs have been placed by the highway department informing the travelling public of the character of the curve. In order to do this successfully, we need to know which signs should be used, and how to properly place them.

Before we discuss how to determine which sign to use, we need to remember what the curve and turn signs are telling the traveling public. Black-onyellow signs are warning signs. These particular ones provide information to the motorist about the nature of the curve they are approaching. They let the driver know if it is a sharp turn or just a gradual curve. Supplemental plates provide an advisory speed for traveling around the curve.

What does the Advisory Speed mean?

The advisory speed for a curve is NOT the safe speed for every vehicle and pavement condition. The advisory speed is a relative value that, for most vehicles, under WET pavement conditions, provides an adequate margin of safety and is reasonably comfortable for most drivers. On a snowy day, for example, we may need to drive even slower than the advisory speed.

It is important to have a consistent, uniform method of placing curve signs. If every curve is posted consistently, the traveling public will have a better understanding of how to drive when they see a particular sign. On the other hand, if some curves are posted differently, the driver may not know what the sign means. That is why the sign regulations are named the Manual on Uniform Traffic Control Devices not just the Manual on Traffic Control Devices. Uniformity may be the most important aspect of all signage, not just curve signs.

Determining Which Signs to Place

The choice of which specific sign to place on a curve depends upon several different factors. The number of curves in a series, the advisory speed of the sharpest corner, and the alignment of the first curve, all help to determine which sign to place. When deciding whether to group curves as part of a series, determine if they have the same alignment (for example, two curves to the left or two to the right). If two curves have the same alignment and are separated by more than 200 feet of straightaway, sign them separately. If two curves have opposite alignments (for example, one to the left and then one to the right) and the distance between them is less than 600 feet, group them together. Sequential curves can always be signed separately if needed, just be sure that the sign placement is not confusing to motorists.

Table 1 on page 3 shows the different signs used to provide information to the public. If the advisory speed is less than or equal to 20 mph, we place turn signs (W1-1 and W1-3). At 35 mph or more, we use curve signs (W1-2 and W1-4). At speeds of 25 and 30 mph, either type of sign may be used. The determination of which sign to use should be based upon a study of the geometry and general appearance of the curve(s). A W1-5 is used whenever there are three or more curves in a series. If there are more than four curves in a row, additional signs are warranted in the middle of the series. Table 1 also shows the different sign types used for various roadway configurations. An L (left) and R (right) designation is used to define the direction/orientation of the first turn.

Determining the Advisory Speed

To determine the recommended advisory speed, we could carefully measure the maximum superelevation on the curve. However, if there are any bumps or depressions, they may be missed by such a survey. In addition, these surveys can take lots of time to conduct (especially with proper traffic control in place the entire time). A faster, safer, and easier method is to use a Ball Bank Indicator. In a Ball Bank Indicator, a ball held in fluid moves in response to travelling around a curve. The goal of a ball bank study is to determine the speed of travel where the ball stays below the maximum reading. The posted speed is usually rounded down to the nearest 5 mph.

It is important to follow correct procedures when using the ball bank indicator, or incorrect readings may result. The safe ball bank indications are shown in Table 2 (below). These indications are designed to provide for safe comfortable travel around the curve. At slower driving speeds, the maximum ball bank readings are higher. As a reminder, these values are different than the values in the older Volume 17B. They are also different than the values in the National MUTCD. The maximum ball bank readings shown in table 2 are proposed for the NYS Supplement, but have been approved by FHWA.

How to Use a Ball Bank Indicator

Ball Bank Indicator
Figure 1 - Ball Bank Indicator

  1. Mount the ball bank indicator on the dashboard of a standard automobile. Sports cars, trucks, and SUVs with heavy-duty suspensions are not recommended for use. They tend to over or underestimate the curve speeds. Since one of the primary goals of signage is uniformity, a sedan or other typical automobile is recommended for speed studies.
  2. Level the ball bank indicator. This is done on a level surface with two people in the stationary car. Two people are recommended for safety reasons. One person can drive and the other person can record the ball bank reading.
  3. Signs used to Indicate Various Curve Configurations
    Table 1 - Signs used to Indicate Various Curve Configurations

  4. Take a series of ball bank readings at various speeds. The driver should drive smoothly, in the center of the lane, at a relatively slow speed. Cutting the corner will result in a higher indicated advisory speed than you should have, while jerking the wheel will result in a lower advisory speed indication. The highest observed ball bank reading should be recorded. Additional runs should be made, increasing the speed 5 mph each time, until the maximum recommended speed is found. An additional run above the maximum recommended speed indication may be done (if the pavement is dry) to confirm the results of the previous reading.
  5. Table 2-Ball Bank Recommended Speed Indications*
    Speed Range
    Maximum Ball
    Bank Reading
    < 20 mph
    16°
    25-30 mph
    14°
    ≥30 mph
    12°
  6. Be sure to check the curve in both directions of travel. The posted speed may be different in opposite directions. If so, post each direction separately. Drivers only can use signs they see.

Important Points to Remember

The placing of curve signs is a critical communication tool with the traveling public. They are not regulatory signs and the actual speed driven around the curve will likely be different. The vehicle type, weather, and driver ability can all affect the actual speed. The goal is to provide a consistent message to alert the driver to the nature of the roadway they are about to travel.

Example Ball Bank Study

Here is a form you can use to perform ball bank studies on your roads and streets. The bottom one is a completed example, showing how how the form is used. For situations where you want to study several curves at once, a form for use with multiple curves is available in PDF format, as well as a single-curve form (example below).

Example of a ball bank test

*Information updated February 2014

Fall 2007

CLRP Library logo

Creative Commons Attribution-Noncommercial-Share Alike 3.0 Unported License icon

This work by the Cornell Local Roads Program (CLRP) is licensed under a Creative Commons Attribution-Noncommercial-Share Alike 3.0 Unported License.